High-Efficient Energy-Saving Multi-Effect Evaporator for Chemical Industry
Multiple Effect Evaporation
Multiple Effect Evaporation remains one of the popular methods used for the concentration of aqueous solutions.
The chief factor influencing the economy of an evaporator system is the number of effects.
By increasing the number of effects we can increase the economy of an evaporator system.
The first effect of a multiple effect evaporator is the effect to which the raw steam is fed.
Vapors obtained from first effect act as a heating medium for another effect.
TVR or MVR is used in Multiple Effect Evaporators to use the dead vapors.
For an evaporator maximum boiling temp is 80℃ in first stage and 40℃ in the last.
Material process
(1) The raw material is delivered to the front primary preheater by the feed pump through the electromagnetic flowmeter, and then enters the top of the primary effect heater through the liquid distributor for primary falling film evaporation and concentration;
(2) The first effect concentrated liquid is transported to the top distributor of the second effect heater by the first effect bottom material circulating pump for secondary falling film evaporation concentration.
(3) The second effect concentrated liquid is transported to the top distributor of the third effect heater by the second effect bottom material circulating pump for third times of falling film evaporation concentration;
(4) Third effect concentrated liquid discharge, according to the online detection of the hydrometer, real-time detection of the material concentration, if the material concentration reaches the set requirements, it will be interconnected with the discharge valve to open the discharge valve and transport the material to the finished product tank, otherwise, it will open the material circulation valve to make the material recycle into the evaporator again for re evaporation.
Steam process
The raw steam enters the primary effect heater for heating evaporation concentration: the secondary steam generated by the primary effect heats the secondary effect, and so on. The secondary steam generated by the third effect enters the end condenser for condensation cooling, and the condensate water is discharged by the condensate pump.
Condensate process
The condensate water produced by the primary effect preheating the materials through the water transfer pipe at the bottom of the shell, to save the consumption of raw steam;
The condensate water produced by the secondary and third effect is discharged by the condensate pump, and the discharge has reached zero pollution. The non condensing gas is connected to the end condenser by the non condensing gas pipe and discharged by the vacuum pump.
Characteristic
1. Evaporation capacity: From 500Kg/h to 80T/h
2. Material: Stainless steel 304 or Stainless steel 316L;
3. Full closed process, fast and low temperature evaporation;
4. Inside pipes are mirror polishing seamless sanitary pipes, so material is not easy to paste on the pipe. It's easy for cleaning;
5. Low steam consumption: 1kg steam can evaporate 3.5-4 kg water;
6. Low evaporation temperature:part of secondary steam can be inhaled into single-effect heater through spray type hot pressure pump. This would make full use of the heat and the evaporation temperature is low.
7. Large concentration ratio: adopt falling film evaporation, which make the material liquid with larger viscosity be easy to flow and evaporate, hard to scale, short concentration time, the concentration ratio can reach to 1:5.
8. This equipment can realize automatic production, intellectual system management, which is in conformity with GMP standard.
9. Can be designed into different technological process according to the different characteristics of the materials and different users' requirements.
Typical three effect falling film evaporator specifications and technical parameters:
| Parameter/ Specifications | HP-3.0 | HP-4.5 | HP-6.0 | HP-9.0 | HP-12.0 | HP-15 | HP-20 | HP-24 | HP-30 | HP-50 |
| Evaporation capacity(kg/hr) | 3000 | 4500 | 6000 | 9000 | 12000 | 15000 | 20000 | 24000 | 30000 | 50000 |
| Consumption of raw steam(kg/hr) | 900 | 1350 | 1800 | 2700 | 3600 | 4500 | 4500 | 7200 | 9000 | 15000 |
| Vacuum degree of each effect | First Effect | 0 |
| | Second Effect | 448 |
| (mmHg) | Third Effect | 640 |
| Evaporation temperature of each effect | First Effect | 99 |
| | Second Effect | 76 |
| | Third Effect | 53 |
| Steam pressure for evaporation(MPa) | 0.6-1.0(Absolute pressure) |
| Solid content in feed(％) | 6-7(Corn pulp example) |
| Solid content outlet(％) | 42-48(Corn pulp example) |
Working principle chart
Workshop Site
Product Tags:
|
|
High-Efficient Energy-Saving Multi-Effect Evaporator for Chemical Industry Images
|
